Description: A one part, solvent‐free, quick setting, moisture curing polyurethane adhesive specially formulated for water‐ resistant bonding and fast setting. D4 water resistance classification to EN204 and EN205 Uses Bond It PU30 RAPID WOOD ADHESIVE can be used in joinery and carpentry, for bonding garden furniture, staircases, boats, wooden constructions, sandwich panels and insulation materials. It has excellent adhesion to wood, chipboard, laminate, metals, polyurethane, expanded and extruded polystyrene foams, mineral wool, concrete, stone, bricks, gypsum boards and all traditional porous substrates. The adhesive film has very good flexibility and can resist water and frost. Preparation Ensure all surfaces are clean, dry and free from grease, oil or any other contaminants that may hinder adhesion. Application WEAR PROTECTIVE GLOVES. Remove lid and cut the tip off the nozzle to an angle of 45°. Apply the adhesive onto one of the substrates, or to both if the materials are porous. Assemble the parts immediately and clamp for at least 3 hours to achieve maximum bond strength. With the addition of water to one of the surfaces, the adhesive will slightly expand, filling any irregularities in the substrate. Setting Time Bond It PU30 RAPID WOOD ADHESIVE has an open time of approximately 15 minutes. Setting time will be achieved after 3 hours with final bond strength after 24 hours. Coverage 120-150g per m2 depending on substrates. Container Size 750g squeezy bottle. Colour Brown liquid. Shelf Life 12 months from date of manufacture when stored in sealed, original bottles. Storage Conditions Store in cool, dry and well ventilated conditions between 5-25oC. Disposal of Containers Do not leave empty containers where residue could be harmful to children, animals or the environment. Remove any containers to a central disposal point in accordance with local regulations. Health & Safety Please refer to separate material safety data sheet for full handling, use and storage instructions. Keep out of reach of children. It is the users responsibility to determine suitability for use. If in doubt contact our Technical Department for advice. Note: this information is for general guidance only, since site conditions and labour are beyond our control. It is recommended that users make their own tests to determine suitability. HANDLING INSTRUCTIONS: WEAR GLOVES/ SKIN COVERING AT ALL TIMES. However, if your skin comes into contact with PU30 follow these instructions. Please note in some cases skin turns black. If in any doubt contact a medical professional, show the packaging and/or the MSDS available for download from www.bonditgroup.com. 1. Wipe adhesive off with a dry cloth or paper towel. If you just touched the glue, and it hasn’t yet begun to dry, you should be able to remove it this way. 2. Wash your hands with soap and cold water. If the adhesive hasn’t started hardening, you have a chance of washing it off. The window for this is small so act quickly. 3. Exfoliate. Use a pumice stone or other gritty textured material (eg. soap with sand in it) to rub at the glue until it comes off. Do this slowly and patiently. Exfoliating too vigorously can damage or burn your skin. Alternate between exfoliating and rubbing the area with your own hand to reduce friction. The glue should begin to ball up and come off. 4. Avoid acetone (nail varnish remover). Acetone will make the glue stick to your skin as it removes your natural oils. Only consider acetone if two body parts are stuck together in such a way that exfoliating is not possible. If this is the case, soak the areas in pure acetone until the glue dissolves enough to pull the skin apart. Forcing this process can tear open the skin, so be patient and work the skin apart slowly. 5. Use a cotton ball dipped in olive oil or vegetable oil to rub off the last remaining bits. This allows you to scrub a little harder without tearing your skin open with the exfoliate. The oil will also act as a moisturiser to your skin. 6. Wash your hands thoroughly. Once you have removed all the glue, it is important to wash your hands thoroughly with soap and water to remove any remaining chemical residue. 7. Moisturise. PU5 glue will dry out your skin, coupled with vigorous exfoliation and hand washing, the natural oils in your skin will likely be stripped causing mild irritations. Use a good hand lotion to soothe the area. Specification Summary Open Time @ 20oC 15 minutes Pressing Time @ 20oC 3 hours Full Cure @ 20oC Approx 24 hours Density 1.13±0.04 g/cm33 Application Temperature Limits +5 to 35oC Temperature Resistance -30 to + 100oC UFI 6590-G0HY-M00W-UDMX Product Details: Part of the Bond It Glues & Adhesives Range Colour: Brown Code: BDAPU375 Size: 750g Barcode: 5060021369338 Package Content: Bond It PU30 30 Minute Rapid Polyurethane Multi Purpose Wood Adhesive Glue 750g
Available Packs: 1,2,3,4,5,6,8 & 10We Accept Payment Via eBay Managed Payment.
Choice: Buyers have more payment options (credit, debit, and gift cards; Apple Pay; Google Pay; PayPal, and PayPal Credit). No separate PayPal account required - for buyers or sellers. Buyers who pay with Apple Pay or Google Pay are likely to be new to eBay.
Any Further Information About Payments. Please Contact US Via eBay Message
Shipping
We use Royal Mail, Parcel Force, Hermes & Yodel for delivery.
Returns