Garage Floor Paint - Concrete - Industrial - Wood - Metal - Walk Way - Quick Set PU350 LOW SLIP OUTSTANDING FINISH EASY APPLY FAST DEL

  Product performance outline:

  To be suitable for use on factory floors industrial floor paints must generally be tough and resistant enough to withstand:-

                The abrasion and wear that will take place i.e. from fork lifts, pallet trucks,cars,4X4 plus other vehicle movements across the factory floor.

                The static loading that is imposed on the painted factory floor surface by pallet stacking in storage, or other equipment on the floor

       Most liquid or chemical spillages that may occur on the floor i.e. Water, oils,Cutting Agents,Soft acid cleaning agents,wheel/brake cleaners,engine coolant,brake fluids some fuel's etc that are used in the processes carried out on the painted  floor.

                (do not leave these to sit on the area coated they must be removed and not left to soak into the area,they will with stand the spill but not for long periods of time)

This is a user friendly coating that can be applied to a professional finish with even the most limited coating or application knowledge,it is a simple remove the lid mix the product to activate and apply with a roller or brush its that simple for the above results in the images.

Most factory floors are reinforced concrete and this must obviously have sufficient strength to support all of these loadings and uses. 

  The functions of the industrial floor paint are: 

  - to strengthen and improve the factory floor surface 

- to eliminate dust build up on surface (pre seal primer coating is always advised on dusty unpainted areas before a topcoat is applied)

- to increase the floors abrasion and wear resistance

- to provide the increased additional chemical resistance

- to control surface dust that is let off from uncoated concrete bases  

- to improve the appearance and ambience of the working environment 

-to speed up the cleaning/mopping of the area cutting down on time of this task and also to help combat dust issues on stock and surface contamination 

- to delineate specific areas, such as: safe walking areas, parking bays or access routes and other directions etc.

This coating can be applied in domestic and industrial areas internal and also external the product is not water proof but will resist rain water when cured. 

Dusty Unstable/Virgin Surfaces

For areas that are dusty and unstable, you will need a product that has been designed for maximum penetration while providing a good film build by re-bonding the substrate together, returning the floor to a solid sound surface the product we advise is our floor primer/underseal this can be found on the floor paint drop down menu.

Oily / Contaminated Surfaces

Where the floors have been subjected to oil and grease, We recommend steam cleaning your floors and use a Heavy Duty Surface Deep Clean before application of any floor coating, after allowing the surface to dry and floor primer or other recommended primer has been applied a top coat can then be applied please do test patches on each stage of this process.

Rising Damp

A floor coating does not do well if you have any moisture issues Hydrostatic pressure from the moisture can actually cause the coating to peel up, sometimes taking pieces of the concrete with it. Should floors be devoid of an effective Damp Proof Membrane (DPM), virtually any paint will lift and peel off the surface. Indeed, even self-levelling screeds can be pushed up by water pressure. This is another nightmare regularly experienced by many companies. For this reason, a damp-proof coating is recommended as a solution before applying a floor paint.

Treating your floor before coating them

It is important to treat your surfaces before coating them to prevent issues post-paint.

Repair your floor:

Before painting your garage floor, it is important to repair any cracks, holes or expansions of joints in your concrete to prevent an un-slightly finish to your flooring once its painted.

New laid areas of concrete should be left to cure for a minimum of 3 months before a floor coatings is applied then surface tests must be done before using this coating contact for free testing information. 

Product & Application information:

coverage:10m squared per litre or 107ft squared per litre

200m squared per 2,100ft squared per 20litre tub (as listed)

(Two Coats Always Advised)

Dry time of coating using standard roller in areas with minimal air moisture (lab conditions)

touch dry @ 15'c = 10/12 hours

in winter months please  allow  extra time for curing,5% white  spirits  can be added to the product in winter months to help with these sub 15'c  temperatures  and help combat slow drying  times, when  coating in these months please still open as many windows and doors possible to create a natural air flow over the coated area a space heater can also be  added, do  not trap warm air as this will also keep the coating  soft as it is a polyurethane product.

do not apply over water, oil or grease any contamination will have to be dealt with before coating of that area get in contact for tips and advise via the message tab on this site.

first coat should be left to dry for 24 hours to assure adhesion to surface leave minimum of 24 hours for after coats always leaving minimum of 48 hours before 100% use of area again

true 100% cure will only be 7 days after application  of last coating

applying multi thin coats is advised and not thick coats. (as thick coatings will surface dry and the under layer will remain soft)

work in a well ventilated area,using no forms of naked light/fire

please test for damp before coating by applying a small test patch or applying a clear plastic sheet (30cmx30cm) and sealing it to the floor with a high grade tape (duck tape) with out any ways of air escaping and leave for 24 hours if there is any forms of water vapour on the sheet the are will have damp and steps will need to be taken before coatings

  Mix very well before use  using a drill/paddle tool

  If the area you are looking to coat is virgin (never been coated) or has had contamination from oil,grease,cutting agents etc,Cleaning with correct equipment/surface preparation products will be required.

quick tip:on virgin surfaces or areas with adhesion issues with past coatings apply a small amount of water to the bare concrete if the water beads on the top the surface will need acid etching or abrading if the water soaks in then it will be fine to start steps towards coating.

  The area will then need to be coated with a heavy duty pre seal and left to dry for 24 hours (you can purchase this pre seal on the drop down menu) do not use pva as this is only a wood glue and not a stable layer for industrial coatings to adhere to.

Powerfloated/Screed areas (smooth shinny concrete) will need to be treated with a acid etch or abrade by mecanical means all product info will be displayed on the item you will take collection of product safety data sheets can be requested on all our range.

a test patch is always advised as some areas my still have contamination and this could have complications when coating 

product weight 20kg minimum our delivery service will bring the product to your door saving you any issues with moving heavy items from there vehicle.

24 HOUR DOOR TO DOOR TRACKING AS STANDARD WITH ALL OUR ITEMS

IMPORTANT:

TO ENSURE DELIVERY EFFICIENCY 

A CONTACT NUMBER IS REQUIRED AT TIME OF PURCHASE

  please add a contact number to "add note"on payment page just before clicking to pay

the delivery company will only try twice to deliver the goods we provide live tracking details and links to the transport web site if contact number provided you will also receive a  complementary text message with a delivery window and also details if you would like to leave the item somewhere safe or delivery at a better time (all changes are at the customers own risk and we will not be held responsible for any theft of items left safe if no one is about to sign for) all vehicles have tracking and cctv for customer reassurance.

Other Important information:

  seller reserves right to cancel any purchase/payment and offer refund in full at any time 

shade variation can happen when orders are made at different times we do work to keep this at a minimum please make sure enough product is ordered at time of purchase. 

or keep a note of batch code from lid of can

PRE-SEAL ITEM IS A UNDERCOAT/SURFACE SEAL AND SHOULD ALWAYS BE OVER COATED WITH A FLOOR PAINT PRODUCT THE PRE-SEAL PRODUCT ON ITS OWN WILL NOT ACT AS A STABLE FLOOR COATING

Floor-paint Products are polyurethane heavy duty high impact formulation and care should be taken when applied full safety data and coshh sheet can be requested 

all images are for illustration purposes only and shade difference may happen from image to product

any further information can be requested via the message service or our contact us tab

we do have some postage limitations we are constantly in contact with many transport companies as we do no agree with these extra charge for some scottish and island postcodes but please get in contact for up to date price and delivery time to these areas:

all of Isle of Wight, Isle of Man and Isle of Scilly and The Highlands and Islands and also the following area postcodes

DD, DG, EH, FK, KA, KW, KY, ML, TD, AB,PA,PH 95% of these postcodes are 3/4 day service 

All products are supplied and provided on the condition that we cannot be held responsible in the event they are used for any other purpose than that specified by the manufacturer, We the seller (RS SUPPLIES)   shall not be liable to the customer in the event of damage to goods/property, injury to persons resulting from negligent or improper use/application or handling/advice of goods by the customer or their employees

Any recommendations and advice offered are given without legal responsibility.   shall not be liable to the customer in the event of damage to goods/property or injury to persons resulting from negligent or improper use/ application or handling/or advice of goods by the customer, their employees or their agents or members of the general public, or any loss of profit or contracts or other consequential losses of any kind however caused.

To the extent permitted by applicable law, We the seller (RS SUPPLIES)  disclaims all warranties, express or implied, as to the accuracy of the information contained in any of the materials on this website.

We the seller (RS SUPPLIES)  shall not be liable to any person for any loss or damage which may arise from advice given or from the use of any of the information contained in any of the materials offered on this website.

for our full terms and conditions please contact us via the message us link on this site.

not to be used on bitumen type floors always do a test patch prior to coating a whole area.