Safety Seal original tyre repair is the fast, safe and permanent method for repairing punctures in tubeless tyres.
With Safety Seal it is easy to quickly and permanently repair a puncture . The repair plug is inserted through the puncture hole and vulcanises together with the tyre rubber, creating a complete and permanent seal.
Read more about how Safety Seal compares with other repair methods .
Tyres repaired with our PLUS Kit have been tested by TÜV in Germany against standard ECE R 30 for car tyres, at speeds over 300 km/h (186 mph), as well as ECE R 54 for truck tyres - the same standards that new tyres are tested against.
The manufacture of Safety Seal plugs is only done in-house at Safety Seal International Inc. to a closely guarded formula. The plug is composed of 21 custom-made filaments with extremely high tensile strength - soaked in a self-vulcanising, air-sealing butyl rubber compound corresponding to 300% of the filaments' weight.
Accept no imitation tyre repair plugs - Safety Seal is the original repair plug for tubeless tyres. The difference is obvious if you compare with others side by side.
This is a permanent repair.
Your Purchase
You are purchasing a Safety Seal Car Plus Tubeless Tyre Repair Kit Large.
Kit Includes:
· Hard Wearing ABS Case · Repairs Plugs 10cm x 60 · External Insert Tool 13cm x 1 · Internal Insert Tool 12cm x 1 · Probe x 1 · Spare Insert Needle 13cm x 1 · Safety Seal Lube x 1 · Knife x 1 · Inner Liner Prep + Primer 1l x 1 · Liquid Patch Tyre Repair 470ml x 1 |
The Safety Seal Large Car Plus Kit provides an easy and cost effective way to repair a car tyre with option of removing the wheel to do an internal repair or an external repair without removing the wheel. This kit allows you to carry out 60 car tyre repairs at a cost of £1.99 each repair.
Safety Seal Internal Repair Step by Step Guide
Car Plus Tubeless Tyre Repair
Step 1. Remove object and note direction of hole. Carefully remove the object that caused the puncture. Note the direction of the puncture hole. When repairing small holes, widening the hole with an awl is required to facilitate the introduction of the repair plug. The size of the damage may not exceed 6 mm for passenger car tyres and 9 mm for truck tyres.
Step 2. Clean the inner liner Clean the inner liner thoroughly with SAFETY SEAL PLUS Inner Liner Prep & Primer around the puncture. Pour SAFETY SEAL PLUS Inner Liner Prep & Primer directly onto the inner liner and rub with a cloth. Repeat this at least once.
Step 3. Insert the tool, thread the plug into the needle's eye
Lubricate the tip of the tool needle with SAFETY SEAL Special Lube. Push the needle through the puncture hole, in the direction of the damage, from the inside of the tyre. Rotate the tool a few times. Thread the repair plug into the needle's eye.
Step 4. Pull the plug through the hole Pull the tool slowly and steadily back with the repair plug, through the hole, until the ends of the repair plug protrude about 10 mm from the tyre tread surface.
Step 5. Apply SAFETY SEAL The Liquid Patch on the inner liner Apply a generous layer of SAFETY SEAL The Liquid Patch on the inner liner, on and around the base of the repair plug. There is a brush on the inside of the jar’s lid for application.
Step 6. Trim off excess material Trim off any excess material flush with the tyre surface, using the knife provided. The tyre is now ready for use.
Note! - When repairing tyres with speed rating V and above, as well as Run-Flat and other "self supporting tyres" – always follow the manufacturer's recommendations. - The components of the SAFETY SEAL PLUS kit are specially designed to be used together. Do not substitute any of the components with any other repair materials.
Safety Seal External Repair Step by Step Guide
Car Plus Tubeless Tyre Repair
Step 1. Remove the object Carefully remove the object that caused the puncture. Note the direction of the puncture hole. If it is difficult to determine, lubricate the eye of the needle and insert the needle into the hole to feel the direction. If major damage is suspected, it is recommended that the tyre be removed for internal inspection.
Step 1a. Broaden the hole with the probe if required For the repair of small holes, it is advisable to broaden the hole with the probe / needle to enable the insertion of the plug.
Step 2. Thread the repair plug into the tool 2. Thread the repair plug into the eye of the tool’s needle. Lubricate the needle's eye lightly with SAFETY SEAL Special Lube. Inflate the tyre.
Step 3. Push in the tool Slowly push in the tool.
Step 4. Pull out the needle Hold the collar of the tool firmly against the tyre with one hand, whilst pulling the needle out with the other.
Step 5. Trim off excess material Trim off any excess material flush with the tyre surface, using the knife provided.
Step 6. Adjust the tyre pressure Adjust the air pressure. The tyre is now ready for use.
NOTE! When repairing tyres with speed rating V and above, as well as Run-Flat and other "self supporting tyres" – always follow the manufacturer's recommendations.