See Details on eBay

Fluke 435-Ii Series Ii Power Quality & Energy Analyzer Brand New

£5,140.72 or Best Offer Unsold, £113.85 Shipping, 30-Day Returns

Seller: computer_psycho (13,638) 100%, Location: Van Nuys, California, Ships to: Worldwide, Item: 323310445526 When ordering from the US, parcels may be subject to import tax and duty charges, which the buyer is responsible to pay. SERIOUS BIDDERS ONLY! PLEASE READ THE DESCRIPTION CAREFULLY! You are bidding on the following: *** BRAND NEW *** FLUKE 435-II SERIES II 3 PHASE POWER QUALITY ANALYZER W/ IFLEX CURRENT CLAMPS (NON BASIC MODEL) MODEL: FLUKE 435-II Retail: $8200 Item Details: Manufacturer: FLUKE Description: Think of the Fluke 435 II Power Quality and Energy Analyzer as your insurance policy. No matter what goes wrong in your facility, with the 435 II you will always be prepared. Equipped with advanced power quality functions and energy monetization capabilities, there is no electrical issue this model can’t handle. Applications PowerWave data capture – capture fast RMS values to see every waveform so you can determine how the voltage, current and frequency values are interacting Power inverter efficiency – Power inverter efficiency Energy monetization – calculate the fiscal cost of energy waste due to poor power quality Energy assessment – quantify the before and after installation improvements in energy consumption to justify energy saving devices Frontline troubleshooting – quickly diagnose problems on-screen to get your operation back online Predictive maintenance – detect and prevent power quality issues before they cause downtime Long-term analysis – uncover hard-to-find or intermittent issues Load studies – verify electrical system capacity before adding loads Features: Power inverter efficiency: Simultaneously measure AC output power and DC input power for power electronics systems using optional DC clamp. PowerWave data capture: Capture fast RMS data, show half-cycle and waveforms to characterize electrical system dynamics (generator start-ups, UPS switching etc.). Energy loss calculator: Classic active and reactive power measurements, unbalance and harmonic power, are quantified to pinpoint the fiscal costs of energy losses. Troubleshoot real-time: Analyze the trends using the cursors and zoom tools. Highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance. Measure all three phases and neutral: With included four flexible current probes with enhanced thin flex design to fit into the tightest places. Automatic Trending: Every measurement is always automatically restringsd, without any set-up. System-Monitor: Ten power quality parameters on one screen according to EN50160 power quality standard. Logger function: Configure for any test condition with memory for up to 600 parameters at user defined intervals. View graphs and generate reports: With included analysis software. Battery life: Seven hours operating time per charge on Li-ion battery pack. PowerWave data capture For some users, loads switching is a cause of power quality problems. When loads switch on, the current draw sometimes causes the voltage to drop to a level that causes other equipment to malfunction. The PowerWave function available in the 435 and 437 Series II models enables users to capture voltage, current and frequency signals simultaneously at a high speed to see which interaction is potentially causing problems. PowerWave goes beyond standard power quality measurements; PowerWave’s fast data capture mode enables system dynamics to be characterized. Waveforms for voltage and current are continuously captured for the specified time, and are displayed on screen in high detail; the power waveform is derived from the data. In addition, half-cycle RMS values for voltage, current, power and frequency can be stored and retrieved for analysis. This feature is particularly useful for testing of standby generation systems and UPS systems where reliable switch-on can be vital. Power inverter efficiency Power inverters take DC current and transform it into AC current, or vice versa. Solar generation systems usually include an inverter that takes the DC energy from the solar cells and converts it to useful AC power. Inverters can lose performance over time and need to be checked. By comparing the input power with the output power you can determine the system efficiency. The 430 series II can measure the efficiency of such inverters by simultaneously measuring the DC and AC power of a system to determine how much power is lost in the conversion process. Unified power measurement Previously, only experts could calculate how much energy was wasted due to power quality issues; utilities could calculate the cost, but the required measurement process was beyond the reach of average electricians. With the new, patented Unified Power function of the 430 Series II, you can use one handheld tool to determine how much power is being wasted, and calculate exactly what the extra consumption costs. Fluke’s patented Unified Power Measurement System provides the most comprehensive view of power available, measuring: Parameters of Classical Power (Steinmetz 1897) and IEEE 1459-2000 Detailed Loss Analysis Unbalance Analysis Unbalance Analysis These UPM calculations are used to quantify the fiscal cost of energy loss caused by power quality issues. The calculations are computed, along with other facility-specific information by an Energy Loss Calculator that ultimately determines how much money a facility loses due to wasted energy. AutoTrend - Quickly see the trend Unique AutoTrend gives you fast insight into changes over time. Every displayed reading is automatically and continuously restringsd without having to set up threshold levels or having to manually start the process. You can quickly view trends in voltage, current, frequency, power, harmonics or flicker on all three phases plus neutral. SystemMonitor - Check performance against EN50160 with ease With a single push of a button, the unique System-Monitor gives you an overview of power system performance, and checks the compliance of incoming power to EN50160 limits or to your own custom specifications. The overview is shown on a single screen, with color-coded bars clearly indicating which parameters fall outside the limits. The System-Monitor overview screen gives instant insight into whether the voltage, harmonics, flicker, frequency and the number of dips and swells fall outside the set limits. A detailed list is given of all events falling outside the set limits. Logging function allows you to customize measurement selections and provides instantaneous analysis of user-selectable parameters. Measure and record power (W), VA and VARs, PF and energy consumption. Track harmonics up to the 50th, and measure and record THD in acstringnce with IEC61000-4-7 requirements Specifications: Product specifications Model Measurement range Resolution Accuracy Volt Vrms (ac+dc) 435-II 1 V to 1000 V phase to neutral 0.01 V ± 0.1% of nominal voltage**** Vpk 1 Vpk to 1400 Vpk 1 V 5% of nominal voltage Voltage Crest Factor (CF) 1.0 > 2.8 0.01 ± 5 % Vrms½ 435-II 0.1 V ± 0.2% of nominal voltage Vfund 435-II 0.1 V ± 0.1% of nominal voltage Amps (accuracy excluding clamp accuracy) Amps (ac +dc) i430-Flex 1x 5 A to 6000 A 1 A ± 0.5% ± 5 counts i430-Flex 10x 0.5 A to 600 A 0.1 A ± 0.5% ± 5 counts 1mV/A 1x 5 A to 2000 A 1A ± 0.5% ± 5 counts 1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 0.5% ± 5 counts Apk i430-Flex 8400 Apk 1 Arms ± 5 % 1mV/A 5500 Apk 1 Arms ± 5 % A Crest Factor (CF) 1 to 10 0.01 ± 5 % Amps½ i430-Flex 1x 5 A to 6000 A 1 A ± 1% ± 10 counts i430-Flex 10x 0.5 A to 600 A 0.1 A ± 1% ± 10 counts 1mV/A 1x 5 A to 2000 A 1A ± 1% ± 10 counts 1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 1% ± 10 counts Afund i430-Flex 1x 5 A to 6000 A 1 A ± 0.5% ± 5 counts i430-Flex 10x 0.5 A to 600 A 0.1 A ± 0.5% ± 5 counts 1mV/A 1x 5 A to 2000 A 1A ± 0.5% ± 5 counts 1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 0.5% ± 5 counts Hz Hz Fluke 435 @ 50 Hz nominal 42.500 Hz to 57.500 Hz 0.001 Hz ± 0.01 Hz Fluke 435 @ 60 Hz nominal 51.000 Hz to 69.000 Hz 0.001 Hz ± 0.01 Hz Power Watts (VA, var) i430-Flex max 6000 MW 0.1 W to 1 MW ± 1% ± 10 counts 1 mV/A max 2000 MW 0.1 W to 1 MW ± 1% ± 10 counts Power factor (Cos j/DPF) 0 to 1 0.001 ± 0.1% @ nominal load conditions Energy kWh (kVAh, kvarh) i430-Flex 10x Depends on clamp scaling and V nominal ± 1% ± 10 counts Energy loss i430-Flex 10x Depends on clamp scaling and V nominal ± 1% ± 10 counts Excluding line resistance accuracy Harmonics Harmonic order (n) DC, 1 to 50 Grouping: Harmonic groups according to IEC 61000-4-7 Inter-harmonic order (n) OFF, 1 to 50 Grouping: Harmonic and Interharmonic subgroups according to IEC 61000-4-7 Volts %f 0.0 % to 100 % 0.1 % ± 0.1% ± n x 0.1 % %r 0.0 % to 100 % 0.1 % ± 0.1% ± n x 0.4 % Absolute 0.0 to 1000 V 0.1 V ± 5% * THD 0.0 % to 100 % 0.1 % ± 2.5 % Amps %f 0.0 % to 100 % 0.1 % ± 0.1% ± n x 0.1% %r 0.0 % to 100 % 0.1 % ± 0.1% ± n x 0.4 % Absolute 0.0 to 600 A 0.1 A ± 5% ± 5 counts THD 0.0 % to 100 % 0.1 % ± 2.5 % Watts %f or %r 0.0 % to 100 % 0.1 % ± n x 2% Absolute Depends on clamp scaling and V nominal — ± 5% ± n x 2 % ± 10 counts THD 0.0 % to 100 % 0.1 % ± 5 % Phase Angle -360° to +0° 1° ± n x 1° Flicker Plt, Pst, Pst(1min) Pinst 0.00 to 20.00 0.01 ± 5 % Unbalance Volts % 0.0 % to 20.0 % 0.1 % ± 0.1 % Amps % 0.0 % to 20.0 % 0.1% ± 1 % Mains signaling Threshold levels Threshold, limits and signaling duration is programable for two signaling frequencies — — Signaling frequency 60 Hz to 3000 Hz 0.1 Hz Relative V% 0 % to 100 % 0.10 % ± 0.4 % Absolute V3s (3 second avg.) 0.0 V to 1000 V 0.1 V ± 5 % of nominal voltage General specifications Case Design Rugged, shock proof with integrated protective holster Drip and dust proof IP51 according to IEC60529 when used in tilt stand position Shock and vibration Shock 30 g, vibration: 3 g sinusoid, random 0.03 g 2 /Hz according to MIL-PRF-28800F Class 2 Display Brightness: 200 cd/m 2 typ. using power adapter, 90 cd/m 2 typical using battery power Size: 127 mm x 88 mm (153 mm/6.0 in diagonal) LCD Resolution: 320 x 240 pixels Contrast and brightness: user-adjustable, temperature compensated Memory 8GB SD card (SDHC compliant, FAT32 formatted) standard, upto 32GB optionally Screen save and multiple data memories for storing data including recordings (dependent on memory size) Real-time clock Time and date stamp for Trend mode, Transient display, System Monitor and event capture Environmental Operating temperature 0 °C ~ +40 °C; +40 °C ~ +50 °C excl. battery Storage temperature -20 °C ~ +60 °C Humidity +10 °C ~ +30 °C: 95% RH non-condensing +30 °C ~ +40 °C: 75% RH non-condensing +40 °C ~ +50 °C: 45% RH non-condensing Maximum operating altitude Up to 2,000 m (6666 ft) for CAT IV 600 V, CAT III 1000 V Up to 3,000 m (10,000 ft) for CAT III 600 V, CAT II 1000 V Maximum storage altitude 12 km (40,000 ft) Electro-Magnetic-Compatibility (EMC) EN 61326 (2005-12) for emission and immunity Interfaces mini-USB-B, Isolated USB port for PC connectivity SD card slot accessible behind instrument battery Warranty Three years (parts and labor) on main instrument, one year on accessories Included accessories: BC430 Power Adapter International plug adapter set BP290 (Single capacity Li-ion battery) 28 Wh (8 hours or more) TLS430 Test lead and Alligator clip set WC100 color coding clips and regional decals i430flex-TF, 24 inch (61 cm) length, 4 flexible current probes 8 GB SD card PowerLog on CD (includes operator manuals in PDF format) USB cable A - Mini B Condition: NEW Auction Details: Shipping: All domestic packages will be shipped out via Fedex or UPS within the lower 48 states Shipping to Hawaii and Alaska would be extra, and those shipments will be shipped out via USPS priority mail, unless otherwise stated in the auction or negotiated in emails. Shipping to APO, RR, or PO box will be handled via USPS and would be extra on certain items, please email us prior bidding. Goods will be dispatched the latest in 2 business days. Goods will be shipped out after the holidays and weekends. No local pick ups accepted at this time, unless otherwise stated in the auction Shipping costs are set at that price to cover some of our costs and packaging and handling fees as well as some of the ebay and paypal fees which add to about 8.5% of the total end price. Please don't email us to negotiate about the shipping costs. We are extremely busy, so we might not answer your emails. Shipping and handling fees are not negotiable, by bidding on this item the buyer agrees to pay for all the shipping costs, failure to do so will result a non paying bidder. We ship to any destination in the world. INTERNATIONAL BUYERS: The International shipping rate is flat rate to most destinations in the world, please email us for additional information. California buyers are subject to pay 9.25% tax. International buyers are responsible for all tax and custom duty charges outside the country. Payment: U.S. Buyers: Credit cards through PayPal Please note that we can't accept direct credit card payments at this time International Buyers: PayPal or Wire Payment is due within 14 days of auction closing. If payment is not received within this time unless otherwise stated or negotiated, item will be relisted on eBay. And the buyer would be reported as NON-PAYING bidder. Terms & Conditions: After the auction is closed, auction winners should contact us within 3 days regarding any questions or requests. After the auction is closed, payment should be received within 14 days. A non paying bidder will be filed with ebay after 14 days of non received payment. All sales are final Any returned non-defective item(s) is subject to 20% restocking fee Shipping and handling charges are not returnable Items will be replaced or exchanged in case of DOA If the same item or similar item is not in stock in case of DOA, the buyer will receive a refund back We combine shipping to save customers money, however, there will be an additional charge per item, please read the description for each item to find out about the specific fees. All buyers are subject to pay all taxes and duty fees inside and outside of the United States, failure to do so will result a negative feedback and buyers will be reported to ebay. Our facilities are closed during the weekends and other holidays and there will be no shipments during these time periods. All packages will go out after the weekend or after the holidays. Contact Information: For any questions regarding this or any of our other auctions please use ebay messaging system Track Page Views With Auctiva's FREE Counter Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. MPN 435-II Brand Fluke UPC 95969615563 Condition: New, MPN: 435-II, Brand: Fluke

PicClick Insights PicClick Exclusive
  •  Popularity - 19 views, 0.3 views per day, 57 days on eBay. Good amount of views. 0 Sold, 1 Available.
  •  Price -
  •  Seller - 13,638+ items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.
Similar Items