STC-3018 12/24/220V Temperature Controller Thermostat LCD Digital Dual Display

£12.99 Buy It Now, FREE Shipping, 30-Day Returns, eBay Money Back Guarantee
Seller: riverwoodstores ✉️ (1,607) 99.9%, Location: Fareham, GB, Ships to: GB & many other countries, Item: 185976813958 STC-3018 12/24/220V Temperature Controller Thermostat LCD Digital Dual Display.

STC-3018 Temperature Controller

Can be used for controlling many different heating and cooling devices such as heaters, refrigerators, freezers, heat tapes, vivariums, fermentation tanks, industrial equipment and other temperature controlled systems.

It contains two independent output relays that can be turned ON or OFF as temperature rises or lowers past a thermal threshold that you set.  You can also set a temperature differential between heating and cooling, set a compressor delay to avoid turning a compressor on and off too frequently as well as apply a calibration offset to the temperature reading.

A built in MCU allows you to configure the module using the display and 4 push buttons. All settings can be saved into non-volatile memory andare preserved during a power cycle.  

Features:

  • Temperature Controller used to switch modes between cooling and heating
  • Suitable for automatic switching of refrigeration and heating devices
  • Includes dual display, red display shows actual temperature, blue display shows set/reference temperature.
  • Instruction manual included
  • Ability to set delay (e.g. for compressor refrigeration)
  • Ability to recalibrate temperature if required
  • Includes hysteresis setting
  • Cooling control output delay protection
  • Can change between Celsius and Farenheit
  • Alarm function - display flashes if temperature exceeds temperature limit or sensor error (no noise)
  • High accuracy and wide measuring range.
  • Sturdy and long lasting device
  • Has a large and clear display for better readability.
  • Can be applied to incubator, oil stove, hatching device, refrigerator and so on.

Operating instructions

  • To operate:  Press the RST (reset) button for 3s to start the thermostat. Press again for 3s to turn it off. When the power is applied, the thermostat switches on automatically.
  • Normal mode: The red digital display on the left shows the real-time temperature, the blue digital display on the right shows the set temperature (i.e. when to start the load device). To establish the set temperature reference (blue display), press 'S' (set) once, the blue display will flash, then press up/down to set to the desired temperature (hold down the up/down button to quickly adjust temperature range).
  • Change settings: Pressing the 'S' button for 3s puts the Controller in the setting mode. The red display will show the setting code (see below codes: P0-P6); the blue display will show the codes parameters. Once you are in setting mode, use the up/down buttons to select the desired code on the red display, then press 'S' once; this will flash the blue display, where you can then adjust the parameters using the up/down buttons. Tip: after a few seconds of no activity the controller will revert back to the normal display, so adjust the settings quickly!
Notes: a). there is no positive/negative indicator on the device connections as it include a Diode which provides protection for reverse polarity (i.e. either connection is okay). b). the rear connections includes a second sensor port, however this is not usable on this model. c). Max amperage is 10A, however it is not recommended to have continuous running at max amperage.

Code Instructions:

Code

Function

Default

Set Range

Start or Stop Temperature

0°C/32°F

-50~120°C/-58~248°F

P0

Working mode

H

H/C

P1

Difference set value

2

0.2-10

P2

High temperature alarm value

80°C/176°F

-50~120°C/-58~248°F

P3

Low temperature alarm value

-50°C/-58°F

-50~120°C/-58~248°F

P4

Temperature calibration value

0

-10.0°C~10.0°C

P5

Compressor delay time

0

0-60 Min

P6

Display mode

C

C/F

Specifications:

  • Model: STC-3018
  • Optional Voltage: 12V/24V/110V - 220VAC
  • Material: ABS flame retardant plastic shell
  • Sensor: NTC Sensor (line length is about 1 metre), 4mm diameter
  • Screen Display: Dual Screen Dual Display
  • Temperature range: -55℃~+120℃
  • Machine Power Consumption: <3W
  • Resolution: 0.1 ° C
  • Precision: ±1℃
  • Machine Size: Approx. 75 x 34.5 x 85mm / 3 x 1.4 x 3.3in
  • Installation Opening: Approx. 71 x 29mm / 2.8 x 1.1in
  • Weight: 110g
  • Ambient Temperature: 0~60°C
  • Relative Humidity: 20%~85% (no condensation)
  • Relay contact capacity: max. 10A/240VAC; Heat max.10A/240VAC

Package List:

  • 1 x Temperature Controller with 1 x NTC probe
  • Instruction manual

Note: Please allow slight error due to manual measurement. Thanks for your understanding.

  • Condition: New
  • Voltage: DC 12V
  • Brand: Unbranded
  • Sensor Type: NTC
  • Model: STC-3018
  • Unit Quantity: 1

PicClick Insights - STC-3018 12/24/220V Temperature Controller Thermostat LCD Digital Dual Display PicClick Exclusive

  •  Popularity - 3 watchers, 0.0 new watchers per day, 266 days for sale on eBay. High amount watching. 3 sold, 10 available.
  •  Best Price -
  •  Seller - 1,607+ items sold. 0.1% negative feedback. Great seller with very good positive feedback and over 50 ratings.

People Also Loved PicClick Exclusive