Suit Bultaco Pursang 360 1975 Mk8 Venhill featherlight throttle cable B01-4-008

£12.31 Buy It Now 5d 23h, £1.95 Shipping, 30-Day Returns, eBay Money Back Guarantee

Seller: Top-Rated Seller up-the-shop (22,179) 99.9%, Location: SURREY, Ships to: Worldwide, Item: 201502544344 Image is for illustration purposes only. You will receive a direct OEM (Original Equipment Manufacturer) replacement cable to suit your motorcycle. Suit Bultaco Pursang 250 Mk 8 1975Made in United KingdomWhy buy Venhill Cables? Venhill are an international recommended choice for replacement cables.They give cables much more than a moments thought, in fact they've been developing, manufacturing and distributing cables around the world for almost 50 years.All Venhill throttle cables have a PTFE Teflon liner in the conduit, for reduced friction and heat resistance, which allows a very smooth operating action. Venhill call them Featherlight cables.Throttle cables is available in the following colour choices.BlackSilverBlueRedYellowPlease add & save message at payment stage, stating colour choice. If no message is received, we will send BLACK. Your order will normally be despatched with in 1 to 2 days, excluding weekends and bank holidays. If you're after a cable that isn't listed yet, please send a message using :ask a question, at the bottom of page and we will do our best to help.CABLE INSTALLATION AND MAINTENANCE RECOMMENDATIONSThe following recommendations are given as guide to you help install and set-up your cables and makesure you get the best from Venhill products.INSTALLING A NEW CABLE• Note the routing of the original cable.• Check that the overall dimensions are the same as the old one. Inner cable lengths may beslightly different, as the old cables will have stretched slightly over time.• Before installing the new cable, hold the cable upright and use a few drops of a light 3 in 1 oil or equivilent tolubricate the inner cable. Move the inner up and down to ease the oil down the cable.• When the new cable is ready to be fitted, route the cable carefully and in most cases, as per theold cable, Make sure the cable will comfortably reach its intended connection.• If the original cable routing is via a heat source, make sure that there is a suitable gap betweenthe cable and the heat source.• If cables ties are required to route the cable, leave them loose allowing the cable to move. Tootight and they will restrict the operation of the cable and its ability to move with the handlebars.• For Push-Pull / Open-Close throttle cables, always connect and adjust the pull/ open cable firstwhere possible.• Where nipples require lubrication in levers or linkages, use a small amount of copper grease.Avoid using heavy greases as these will attract dirt, restrict the movement of the nipple and causeexcessive wear and stress on the nipple and cable.• When the cable has been installed, check the steering lock to lock and check the operation of thecable at both extremes of steering. Check that the cable does not go tight and that operation isnot impaired. If one of the above is true, check the cable routing, adjustment and that all thenipples are located properly.MAINTENANCECable maintenance is essential to prolong the life of the cable and maintain the operation of the cable.• MX bikes – After a race meeting or as often as possible after power washing, remove the cablesfrom the bike and flush through with WD40 or equivalent. Keep flushing them through until the fluid runs clear.Once clean, lubricate the cable again with a light 3 in 1 oil and check the cable routing. Alsolubricate nipples where required with Copper grease.• Trail/Trial bikes – When servicing or after power washing, remove the cables from the bike and flushthrough with WD40 or equivalent. Keep flushing them through until the fluid runs clear.Once clean, lubricate the cable again with a light 3 in 1 oil and check the cable routing. Alsolubricate nipples where required with Copper grease.• Road bikes – At the beginning and end of the summer, remove the cables and flush through withWD40 or equivalent. Once clean, lubricate the cable with a light 3 in 1 general purpose oil and lubricate nippleswhere required with Copper grease. Note barrel nipples must be free to rotate in the lever blade.Do not use heavy engine oils, chain lubricants or grease to lubricate cables as this will attract dirt,increase cable wear and reduce the operation of the cable. Remember: Cables are a service item andshould be replaced at regular intervals. If you are in any doubt about replacing or installing a cable, please consult your nearest qualified motorcycle mechanic. Condition: New, Manufacturer Part Number: B01-4-008, Type: Throttle Cable, Brand: VENHILL, Country/Region of Manufacture: United Kingdom

PicClick Insights PicClick Exclusive
  •  Popularity - 749 views, 0.7 views per day, 1,135 days on eBay. Super high amount of views. 1 sold, 1 available.
  •  Price -
  •  Seller - 22,179+ items sold. 0.1% negative feedback. Top-Rated Seller! Ships on time with tracking, 0 problems with past sales.
Similar Items